How to manually retract an RV slideout in its extended?

Gary Bunzer, the RV Doctor, explains how to manually retract an RV slideout that is stuck in its “out” position. Upload, livestream, and create your own videos, all in HD.

What do you need to know about electric slide out?

Simply take the crank handle (through-frame models) or wrench, ratchet or drill with a nut driver (in-frame models) and rotate it clockwise to retract and counterclockwise to extend slide-out. It is important to note that you DO NOT need to attempt to disengage the motor as the actuator is “manual ready” Just hook up and crank.

Why does my slide not retract after new motor?

After the new motor was installed, the slide still would not retract. The “square rods” connected to the motor were detached to assure the new motor was functioning. We found that power to the motor existed only when the “out” part of the slide’s in/out button was pushed. There was no power to the motor when the “in” side of the button was pushed.

Where are the rods that drive the slide out?

The opening is just to the left and below the yellow wire screw caps (first photo with old motor) Square rods that drive the slide bars are attached on both sides of the motor gear box (second photo with new motor). The slide-out that was stuck open is also shown below.

Gary Bunzer, the RV Doctor, explains how to manually retract an RV slideout that is stuck in its “out” position. Upload, livestream, and create your own videos, all in HD.

How does a hydraulic slide out system work?

In the electrical slide-out, the motor directly does the work of moving the slide out room. In the hydraulic slide-out, the 12-Volt motor powers the hydraulic pump that then provides the pressure to move the slide in or out. On my rig that is the way the engineers designed the system.

What do I need to override the slideout system?

The room is now free to move. Using either a 5/8” or 3/4” wrench or socket, crank the room either in or out completely (depending on your needs). NOTE: If the slideout system is supplied with a gearbox override (optional), use the crank handle to move the room.

How do you retract a slideout room?

Retracting Slideout Room 1. Verify the battery is fully charged and hooked up to the electrical system. 2. Press and hold the IN/OUT switch in the IN position until the room is fully retracted and stops moving. 3. Release the switch. This will lock the room into position.

What causes an RV slide out to not work?

A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work. If the motor-driven gearbox system is faulty, for whatever reason, your RV slide-out will not work. Your RV slide may experience resistance as it moves in and out.

What are the common problems with fifth wheel slide outs?

Each slide-out operating system has its own unique problems. Check out the following common problems with slide-outs on a fifth wheel. A faulty motor or gearbox could be the problem if your RV slide-out gear system is motor-driven. In such cases, if the motor is faulty or breaks down, then the mechanism will not work.

Why does my forest river slide not retract?

Storiing fishing poles from the other side, the metal ends of the pole shorted the P/C board. As always, this will happen when the slide is extended. Ditto for Forest River’s RVs. Level first, extend slides afterward.

Why do I have trouble retracting my slideout?

I don’t know a lot of the details, but it turned out that at the end of the stroke, the slide out dropped so that one of the rack and pinion sets changed center distance enough that the gear teeth disengaged. The retracting load would then fall on only one set of gears thus causing the slideout to skew and bind.

What’s the best way to fix a slide out?

Use a wire brush to remove any debris, dirt, paint chippings or rust from your slide-out tracks. Clean out all the dirt and road debris from the tracks. Apply lubricant on the gears, tracks, and rails of your slide-outs. Try and retract and fully extend your slide-out a number of times. At this point, the squeaking sounds should have disappeared.

How to troubleshoot the Lippert electric slideout system?

TROUBLESHOOTING The Lippert Electric Slideout Systemis only one of four interrelated slideout room system components. These four components are: chassis, room, coach, and Lippert Electric Slideout System. Each one needs to function correctly with the others or misalignment problems will occur.

What causes a slide out to not retract?

With that being said, the biggest issue with slide-outs doesn’t have anything to do with the extension/retraction process. It has to do with seals, the rubber gaskets that surround a slide-out and keep the elements at bay. Improperly installed seals can pull loose and affect movement of the slide.

Can a single pump be used to retract slide outs?

In either instance you will probably find yourself at the mercy of an RV repairman, who may or may not have the parts needed for a quick repair on hand. Also, due to the inherent power of hydraulics, a single pump/motor is often used to extend/retract all slide-outs. When it works, you’re golden.

What to do if your slide out slides are crooked?

To solve this issue, you can remove some of the carpet and replace it with slide out slickers. Or you can shim your slide out slides with thing, 1/4” thick, aluminum flat stock. With the latter method you can interchange the metal and thickness to fit your situation.

Are there any problems with the slide out?

Most slide out problems are not that difficult to trace and then solve. There will be those that require the help of a professional technician to repair. The key would be to get to know your system and learn when the task is beyond your abilities to handle .

Why is my RV slide not going all the way out?

RV Slide will Not Go all the Way Out Most RV problems can be solved by looking for simple obstacles or obstructions first. If this problem is happening to your kitchen slide out then you may have some plumbing lines or other kitchen equipment in the way.

Why is my slide out motor not working?

RV Slide Motor not Working. The bad news is that one of your slide out motors may have died. The good news is that the failure is due to a faulty wire or connection which caused a short and tripped a breaker. The latter may not be the case if you have 2 motors on your slide out and one is still working.

What are the most common problems with Keystone campers?

There are numerous reports of trim strips coming falling off, loose fixtures, and peeling veneer on doors and closets. Unfortunately, this lack of quality also extends to some cases of screws falling out and even mysterious holes in the flooring and walls.

How to override your slide out mechanism Keystone?

This video shows the types of slide out mechanisms Keystone uses in their travel trailers and fifth wheels and provides a step by step explanation on how to override the system to retract your slide out room should you lose power. Loading…

What should I winterize my Keystone RV for?

Winterizing the right way will protect your Keystone RV for the winter and for many camping seasons to come. FAQ: What do RV weight ratings mean? FAQ: Where can I find the VIN or serial number for my Keystone RV? FAQ: Where Can I Find a Keystone RV Owner’s Manual? FAQ: How can I get parts for my RV?

Where is the slideout motor on a RV?

Locate the slideout motor. It will be mounted to one of the slideout rails. NOTE: If the RV has an underbelly or a cover over the motor, these parts must be removed to access the motor. 4. Rotate the brake lever, on the backside of the motor, counter-clockwise (looking from the rear of the motor) about 1/8 of a turn to the released position.

How do you retract a slide out on a travel trailer?

If the crank handle is not available, use a wrench or socket and ratchet to turn the crank extension by hand to extend or retract the slide-out. Reattach the brake assembly to the slide-out motor.

How to override the slideout system in an RV?

There are two versions of the controller. For version 1, unplug the (6) pin wiring harness from the controller. For version 2, remove one of the motor leads, either the motor I or motor II lead from the controller. 3. Locate the slideout motor. It will be mounted to one of the slideout rails.

Is the Lippert slide out controller a problem?

A final update for my slide-out problem. The good folks at RV Masters in Houston diagnosed the problem to be a “bad” Lippert Slide-Out Controller. The “in/out” switch and relay all work fine and were not the problem. A new controller was installed and the slide out is working great again!

Why is my passenger side slide not retracting?

My trip to Baton Rouge for LSU football this past weekend went to heck when my passenger side slide would not retract (we stayed Thursday night in Lake Charles, LA to visit my son’s family). After calling a couple of Lake Charles RV repair shops, the initial thought was the slide motor had quit working.

Can a driver side slide be retracted on a disco?

If neither of these are possible they say the slides should be moved only with fully charged batteries. On the Disco, the driver side slide fits flush to the floor when extended. The three men are getting it over the ramp to retract. There is a replacement motor with higher torque available.

What should I do if my slideout is not aligned?

Extend and retract the slide a few times and check for proper room flange sealing. If the room is not properly aligned, repeat steps 1 thru 6. *Depending on the size of your slide, you may need help moving the room by hand.

How much does it cost to fix an RV slide out?

All of these problems should not stop you from manually sliding the slide out in and out. Then if it is a broken gear in the motor, it may cost you about $800 to fix, depending on your dealer or repair shop. Hopefully, your warranty is still valid and you are covered. If not you may want to try to fix it yourself.

How to troubleshoot a forest river travel trailer?

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 pageof56Go /56 Contents Table of Contents Troubleshooting Bookmarks Advertisement Quick Links x Download this manual 28 Electrical System Control 30 Fuses and Circuit Breakers 30

Is the Sierra by Forest River 5th wheels?

TRAVEL TRAILERS/5TH WHEELS – In addition to previously listed items, 2003 values also include stabilizer jacks, upgraded interior lighting, spare tire with carrier and cover and roof rack and ladder. Founded in 1997, the Sierra by Forest River line-up of vacation trailers produces high quality recreational vehicles.

How big is a Sierra by Forest River?

Select a 2003 Sierra by Forest River Series. Founded in 1997, the Sierra by Forest River line-up of vacation trailers produces high quality recreational vehicles. Sierra by Forest River has created travel trailers between the lengths of 25 and 41 feet as well as an array of fifth wheel trailers from 26 to 41 feet long.

Is there a manual override on Lippert slide out?

All Lippert electric slide-out units come with a manual override system. Please watch this video in its entirety before you attempt to manually operate your slide-out system.

Why is the side of my RV slide out Crooked?

On the other hand, a more serious source is that you may have crack in the side out somewhere that is letting the water in. This will be a more expensive fix, although you can do it temporarily and wait till you get home to deal with it. On some slide outs the manufacturer has designed the section so that it will close at the top first.

Why are my slide outs not going in or out?

If you hear a weird noise when you try to extend the slides, it could be the pump trying to work. If you just can’t seem to make those slide outs go in or out, it is possible on most RVs to manually extend or retract the slides.

What to do when slide outs don’t slide in-RVing?

Consult with your owner’s manual to see if there is a way to close the slide out manually when the mechanism that is supposed to handle the job has failed. Most RV’s have some form of manual override to allow you to get back on the road successfully.

Why does a retracting load cause a slideout?

The retracting load would then fall on only one set of gears thus causing the slideout to skew and bind. The problem was solved by adding shims to prevent the change in center distance.

All Lippert electric slide-out units come with a manual override system. Please watch this video in its entirety before you attempt to manually operate your slide-out system.

What should you know about the slideout room?

ALWAYS MAKE SURE THAT THE SLIDEOUT ROOM PATH IS CLEAR OF PEOPLE AND OBJECTS BEFORE AND DURING OPERATION OF THE SLIDEOUT ROOM. ALWAYS KEEP AWAY FROM THE SLIDE RAILS WHEN THE ROOM IS BEING OPERATED. THE GEAR ASSEMBLY MAY PINCH OR CATCH ON LOOSE CLOTHING CAUSING PERSONAL INJURY.

What to do when the slide out doesn’t slide?

A stray item wedged in your slide out can be an easy fix, so go check before tearing your motorhome apart looking for the slide motor. You’ll definitely hear the motor laboring if this is the problem, so make sure to keep an ear out for odd sounds too!

How big of a wrench do you need to move a slide?

If you disengage that lock switch you should be able to put a 3/4 inch wrench/ratchet on the nut to move the slide. If there are two motors on the slide it will require two people and the wrenches need to be turne simultaneously (slide ends within 1 to 2 inches of each other) so do the wrench turns together.

How big of a ratchet do I need to move a slide?

Your manual should state whether to turn the lock switch left or right to engage the lock. If you disengage that lock switch you should be able to put a 3/4 inch wrench/ratchet on the nut to move the slide.

How do you retract a brake on an RV?

You can do this by using a screwdriver to remove the screws that directly connect the brake assembly to the motor itself. Just make sure to safely store the screws, as you will certainly need to use them again. Step 6: Set the brake assembly aside, in some place safe and dry.

Why does my RV slide out not work?

If the RV’s power retractable system runs off the shore power connection, a problem in the shore power system might be at fault. This could be something as simple as a loose connection, a loose wire, a damaged plug or a larger problem with the RV park’s shore power system.

What to do when slide outs don’t move?

Make sure the house batteries are charged completely, or if at all possible, plug your RV into shore power. This will indicate whether the problem may be the batteries or not. If you push the button for the slide outs and can hear the motor running but the slides don’t move, check the motor’s shear pins.

How do you retract slide out motor on RV?

Step 3:Press down and hold the In-Out switch that operates the RV’s power-retractable slide out system. If it does nothing, then you can turn to the manual override system. Step 4:Locate the slide-out motor underneath the slide-out section.

How to manually open an electric slide on a travel trailer?

Make sure the trailer is level before operating the slide-out. Check the battery and verify it is fully charged and connected to the electrical system. Press and hold the wall-mounted In/Out switch. If the slide does not extend or retract, use the manual override to extend or retract the slide-out. Find the slide-out motor.

What to do if your slideout room does not lock?

Install the transit bars to the slideout room (if so equipped) and take the unit to an authorized dealer for service. Warning! WHEN THE MOTOR BRAKE IS DISENGAGED THE SLIDEOUT ROOM WILL NOT LOCK INTO PLACE; THEREFORE, THE ROOM WILL NOT BE SEALED.

Why does my slide out Stick after 8 inches?

If your other slides operate quickly and this one sticks for the first 8 inches, it sounds like there is something that is rubbing or sticking when the slide first starts in. The fact that it moves in normally after the first eight inches suggests that the motor is working well. You haven’t indicated what model and year motor home you have.

How does the Lippert electric slideout system work?

The Lippert Electric Slideout Systemis a rack & pinion guide system, utilizing an electric ball screw actuator to move the room assembly. The motor drives the ball screw in a forward and backward motion to drive the slide room in and out. The actuator comes equipped with an automatic clutching system.

Why is my slide out not working in my RV?

Before you assume that something has broken or is stuck within the slide out mechanism itself, check to see if you are getting enough power from your battery to run the system. You obviously need sufficient voltage from your battery to make the slide out move properly, so an old or worn out battery may be the underlying problem.

Where is the slide out controller on a motorhome?

For my motorhome, there are two slide out controllers attached to the “roof” of the middle basement compartment between the two main beams of the frame. One controller for the passenger side slide-out and one for the drive side slide-out. RV Masters charged $130 for the new controller and $140 for an hour of labor to install the controller.

What to do about squeaking fifth wheel slide out?

Apply lubricant on the gears, tracks, and rails of your slide-outs. Try and retract and fully extend your slide-out a number of times. At this point, the squeaking sounds should have disappeared. Lubricating your RV slide-out mechanism not only eliminates the squeaky sounds, but it also helps it work optimally.

Are there any problems with the slide out on an RV?

Troubleshooting RV Slide Out Problems: One main problem with slide outs is that they may get out of alignment. The good news here is that each slide can be adjusted separately. All you have to do to fix it is take your RV to a dealer and let them make an adjustment.

What causes the slide out on a camper to bind?

Also, if your chassis is bent, that will cause your camper slide out to bind. On top of that, check the openings your slide out is going through. There may be a problem there. Check to see if you have a manual over ride option you can use just in case.

How to manually retract an RV slideout in its extended?