Why are the steps on my Kwikee not working?

There are several possibilities that could do what you have now. One is the motor failed, another the control board has failed, or for some reason the motor does not know the steps have reached the stored position and the motor has not powered down.

What are the step test procedures for Kwikee?

Troubleshooting and Test Procedures The step test procedures outlined in this tip sheet are provided to troubleshoot and test all Kwikee IMGL automatic electric step functions. The procedures are designed to initially check the basic functions of the step separately from the RV wiring to determine whether or not the step is malfunctioning.

Where is the lighted switch on Kwikee steps?

Many rigs with Kwikee steps have a lighted switch near the door. When the light is off, the steps will open and close with the door. When the light is on and the RV’s engine is off, they will stay open all the time once extended.

What does warm motor mean on Kwikee step?

With Kwikee that is detected by the control board when the motor stalls due to reaching the stops and no position switch is involved. A warm motor would seem to imply that the power didn’t shut off like it should when the step reached the stop in the store position.

What are the symptoms of a broken Kwikee step?

In my experience the most common symptoms of a broken Kwikee step are either nothing happens when the door opens and closes, or the wrong thing happens (usually accompanied by an unwanted noise). So continuing down that path, here is the approach I took to troubleshooting my step problems.

Where is the motor on a Kwikee step?

You can find the manual for your Kwikee step model here. The motor is mounted on top of the gear linkage with three bolts. It drives the gear linkage in forward or reverse when activated by the controller. It will stop turning when it can’t move anymore (i.e. step is fully extended or retracted).

How do you replace a motor on a Kwikee?

Using a 10mm socket, remove the 3 screws holding the motor assembly 4. Lower it straight down being certain not to drop the gear, washers and pin on the gear assembly side of the motor 5. Move the washers, gear and pin to the new motor 6. Apply new grease to the gear if needed 7. Insert motor assembly into gear box and insert the three screws 8.

Where do I find the in line fuses on a Kwikee?

I called the Camping World (over 8 hours away & not headed in that direction) that installed them & the service writer agreed it appeared to be an “electrical issue” & suggested I look for an in-line fuse, but I can’t locate any & it’s darn-near impossible to trace the wiring as they are all wrapped together leading into the engine compartment.

Which is the best way to check fuses?

The best way to check fuses is by using an ohm meter and the good ones will read 0 ohms through them, with anything more than a few ohms being bad. There are several possibilities that could do what you have now.

Is the magnetic switch on the Kwikee step control open?

The models after 2005 are all auto retracting and extending so you will use the Lippert Components Kwikee Step Control with Override and PKD # LC379605 instead if you have something newer. The magnetic switch is an open circuit on newer models, but on older models they used a closed circuit.

Which is Lippert control unit for Kwikee steps?

The Lippert Components Kwikee Control Unit for pre-IMGL/9510 Step Control with switches # LC379606 is the fit for 1999-2005 models. The models after 2005 are all auto retracting and extending so you will use the Lippert Components Kwikee Step Control with Override and PKD # LC379605 instead if you have something newer.

Where is the power cable on a Kwikee step?

Follow the black wire bundle from the connector to the black box mounted to the step. That’s the Step Controller. You’ll find several colored wires going into the controller. There should also be a power cable from the controller to the step motor. Refer to the Lippert manuals for your specific Kwikee step model for the correct wiring.

Which is the correct controller module for Kwikee steps?

The correct part may be the solution. The Replacement Control Module for Lippert Electric Coach Step # LC301702 you asked from is not a Kwikee Step controller. The Lippert Components Kwikee Control Unit for pre-IMGL/9510 Step Control with switches # LC379606 is the fit for 1999-2005 models.

How do you fix a stuck motor on a Kwikee?

1. Disconnect power to the step 2. Disconnect the power plug from the motor assembly 3. Using a 10mm socket, remove the 3 screws holding the motor assembly 4. Lower it straight down being certain not to drop the gear, washers and pin on the gear assembly side of the motor 5. Move the washers, gear and pin to the new motor 6.

How long does a Kwikee step finish warranty last?

The warranty is effective as of the date of sale to the original purchaser and extends two years for parts and labor on step mechanisms and one year for step finish. Since it is the responsibility of the owner to verify the original purchase date, Kwikee recommends that a bill of sale or sales receipt be kept for that purpose. 4.

What should I do if my Kali installation fails?

It was unnecessary to do anything fancy, I simply did a non graphical installation with the filesystem “all in one” (for beginners) and it installed with no problem at all. So, if you are failing your installation from USB, may be just try that out and it could work just fine for you also.

How do you turn off auto extend on a Kwikee step?

In this case, the override switch must be turned off for the step to retract. Turn the vehicle ignition off and open the door. The step will extend and lock in the ‘down’ position. This is the ‘Auto Extend’ feature.

Why are the steps on my Kwikee not working?